Home » Harbor Freight Tools Manuals » Tools » Harbor Freight Tools 61969 » Manual Viewer

Harbor Freight Tools 61969 User Manual

Harbor Freight Tools 61969 - 12 in. Double-Bevel Sliding Compound Miter Saw Manual

View all Harbor Freight Tools 61969 manuals

Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 61969 manual content summary:

Harbor Freight Tools 61969 | User Manual - Page 1
future reference. ITEM 61969 12" DOUBLE-BEVEL SLIDING COMPOUND MITER SAW WITH LASER GUIDE REV 14e Note: Blade sold separately. Visit our website at: http://www.harborfreight.com Email our technical support at: [email protected] When unpacking, make sure that the product is intact
Harbor Freight Tools 61969 | User Manual - Page 2
Table of Contents Safety 3 Specifications 6 Setup 7 Operation 10 Maintenance 14 Parts List and Diagram 17 Warranty 20 SAFETY SETUP OPERATION WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety
Harbor Freight Tools 61969 | User Manual - Page 3
at all times. 14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like. 16. REDUCE THE RISK OF
Harbor Freight Tools 61969 | User Manual - Page 4
for 2-Prong Plug.) Miter Saw Safety Warnings For Your Own Safety Read Instruction Manual Before Operating Miter Saw 1. Wear eye protection. 2. Keep hands out any are moved during blade replacement. Check all guards for proper operation after service. 10. The lock down pin is to be used only to lock
Harbor Freight Tools 61969 | User Manual - Page 5
et seq.) 31. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may a doctor and then have regular medical check‑ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people
Harbor Freight Tools 61969 | User Manual - Page 6
SAFETY Specifications Electrical Rating 120V~ / 60Hz / 15A Motor No Load Speed 3,800 RPM Max. Accessory Diameter 12" Arbor 5/8″ Round with 1″ Adapter 90° Straight 3-1/2″ x 13-3/8″ Cutting 45° Miter Capacities 45° Straight Bevel 3-1/2″ x 9-1/2″ 2-1/8″ x 13-3/8″ 45° Compound (L/R)
Harbor Freight Tools 61969 | User Manual - Page 7
the following pages, refer to the Assembly Diagram near the end of this manual. Assembly 1. Insert the ends of the Table Extensions into the holes in provided in the Base to mount the Miter Saw to a stable support before use. Mounting hardware not included. SETUP OPERATION MAINTENANCE Item 61969
Harbor Freight Tools 61969 | User Manual - Page 8
SAFETY SETUP Functions Dust Collection Bag Slide Lock Knob Bevel Angle Indicator Bevel Lock Knob Fence Table Extension Trigger Lock Turntable Trigger Lock Trigger Lower Guard Blade Clamp Miter Scale Kerf Board Miter Lock Miter Knob OPERATION MAINTENANCE Page 8 For technical questions,
Harbor Freight Tools 61969 | User Manual - Page 9
from sliding back and forth for chopping cuts. Loosen this to allow the cutting head to slide. Note: Additional functions are explained elsewhere in the manual. Item 61969 For technical questions, please call 1-888-866-5797. Page 9 MAINTENANCE
Harbor Freight Tools 61969 | User Manual - Page 10
SAFETY Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TOOL SET UP TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn
Harbor Freight Tools 61969 | User Manual - Page 11
place using the Wing Screws. 2. When properly installed, the upper face of the Table Extensions are level with the Table, and provide a wider support surface for the workpiece. 3. Support the workpiece to be level with the table, and so that after the cut is made the cut off pieces will not fall
Harbor Freight Tools 61969 | User Manual - Page 12
and right of saw for extended workpieces. 4. Use a saw table, saw stand or other means to support the workpiece. Mount the Miter Saw so that the surface is level to the ground, and additional supports provide a surface on the same level as the saw table. If the work surface and any workpiece
Harbor Freight Tools 61969 | User Manual - Page 13
General Operating Instructions DANGER! Clamp. Ensure that the work material is level and supported securely, use saw horses or supports if necessary. 7. Press down lightly to cut the the Trigger to start the Saw and the laser guide. Note: If the laser guide line does not line up with the cut line,
Harbor Freight Tools 61969 | User Manual - Page 14
SAFETY SETUP Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE,
Harbor Freight Tools 61969 | User Manual - Page 15
Calibrating the Miter Table Indicator After checking or adjusting the fence to confirm that it is at 90º to the Blade, check the accuracy of the Miter Table Angle Indicator. 1. Loosen the screw holding the Angle Indicator in place. 2. Rotate it until the pointer is exactly on 90º. 3. Retighten the
Harbor Freight Tools 61969 | User Manual - Page 16
Troubleshooting Problem material on Table. Material must be flat, flush against Fence and supported on ends. 1. Keep finished side of material up or facing operator precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. SETUP OPERATION MAINTENANCE Page
Harbor Freight Tools 61969 | User Manual - Page 17
DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES Cover 48 M4×10 Cross Pan Head Bolt 49 Bevel Angle Indicator 50 Turntable Support 51 Gear Column 52 Angle Block 53 M6×16 Non-Standard Screw 54 M6
Harbor Freight Tools 61969 | User Manual - Page 18
SAFETY SETUP Parts List (cont.) Part Description 75 Ø4 Flat Washer 76 M10 Thin Nut 77 M8×18 Left-handed Spindle Bolt 78 Outer Flange 79 Arbor Insert 80 Blade (sold separately) 81 Inner Flange 82 M5×20 Cross Pan Head Bolt 83 Ø5 Spring Washer 84 Ø5 Flat Washer 85 Gearbox Cover 86
Harbor Freight Tools 61969 | User Manual - Page 19
Assembly Diagram (1 0) SAFETY SETUP OPERATION 173 64 191 63 190 189 188 187 186 185 184 192 183 182 181 180 179 178 177 176 126 125 156 157 158 159 160 164 163 Item 61969 For technical questions, please call 1-888-866-5797. Page 19 MAINTENANCE
Harbor Freight Tools 61969 | User Manual - Page 20
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.